Module 1 PSE&G AT Orientation
Unit 1 Orientation: How to get the most out of the PSE&G Advanced Troubleshooting Course
Module 2 Basic Electricity Review
Unit 1 Basic Electricity and Circuits
Unit 2 Electrical Measurements Overview
Unit 3 Using Ohm's Law as a Powerful Troubleshooting Tool
Module 3 Fundamental Troubleshooting Techniques
Unit 1 Troubleshooting and the Ten-Step Tango
Unit 2 Guidelines for Reading Schematics
Unit 3 Special Situations and Techniques
Module 4 Schematic Reading Exercises
Unit 1 Schematic Exercises: Appliances with Electronic Control Boards A
Unit 2 Schematic Exercises: Appliances with Electronic Control Boards B
Module 5 Troubleshooting Appliances with Timer Charts
Unit 1 Analyzing Dryer Timer Motor Operation Using EEPs and the Timer Chart
Module 6 Troubleshooting Appliances with Electronic Control Boards
Unit 1 Troubleshooting Distributed vs. Central Control Systems
Unit 2 Troubleshooting Appliances with Multiple Control Boards
Module 7 Gas Dryer Technology
Unit 1 Dryer Air Movement and Venting Systems
Unit 2 Dryer Motors
Unit 3 Dryer Air Temperature Control Systems
Unit 4 Gas Burner Ignition Systems in Dryers
Unit 5 Dryer Case Studies
Unit 6 Common Problems in Gas Dryers
Module 8 Gas Range Technology
Unit 1 Gas Burner Spark Ignition Systems
Unit 2 Gas Flame Detection
Unit 3 Direct Spark Ignition Systems
Unit 4 Gas Oven Hot Surface Ignition Systems
Module 9 PSE&G Case Study 1: Dual Fuel Range - Gas Surface Burner Continuous Sparking
Unit 1 Case Study 1: Problem Statement
Unit 2 CS1: Schematic Review and Initial Findings
Unit 3 CS1: Load of Interest
Unit 4 CS1: LOI Circuit Analysis
Unit 5 CS1: Troubleshooting Hypothesis
Unit 6 CS1: Select Electrical Measurements & EEPs
Unit 7 CS1: Make "Electrical" Measurements & Compare with Specs
Unit 8 CS1: Case Study Wrap-up
Module 10 PSE&G Case Study 2: Dual Fuel Range - Gas Surface Burner No Ignition
Unit 1 Case Study 2: Problem Statement
Unit 2 CS2: Schematic Review and Initial Findings
Unit 3 CS2: Load of Interest
Unit 4 CS2: LOI Circuit Analysis
Unit 5 CS2: Troubleshooting Hypothesis
Unit 6 CS2: Select Electrical Measurements & EEPs
Unit 7 CS2: Make "Electrical" Measurements & Compare with Specs
Unit 8 CS2: Case Study Wrap-up
Module 11 PSE&G Case Study 3: Gas Range - Bake Burner No Ignition
Unit 1 Case Study 3: Problem Statement
Unit 2 CS3: Schematic Review and Initial Findings
Unit 3 CS3: Load of Interest
Unit 4 CS3: LOI Circuit Analysis
Unit 5 CS3: Troubleshooting Hypothesis
Unit 6 CS3: Select Electrical Measurements and Specifications
Unit 7 CS3: EEPs for Electrical Measurements
Unit 8 CS3: Make Electrical Measurements
Unit 9 CS3: Compare Measurement Results to Specifications
Unit 10 CS3: Case Study Wrap-up
Module 12 PSE&G Case Study 4: Gas Range - Low/Erratic Oven Temperature
Unit 1 Case Study 4: Problem Statement
Unit 2 CS4: Schematic Review and Initial Findings
Unit 3 CS4: Load of Interest
Unit 4 CS4: LOI Circuit Analysis
Unit 5 CS4: Troubleshooting Hypothesis
Unit 6 CS4: Select Electrical Measurements and Specifications
Unit 7 CS4: EEPs for Electrical Measurements
Unit 8 CS4: Make Electrical Measurements
Unit 9 CS4: Compare Measurement Results to Specifications
Unit 10 CS4: Case Study Wrap-up